Edimax IC-7000PTN Manual de usuario

Mechanical Pan & Tilt IP Camera User Manual 1

1.5 Descriptions for LED Indicators For IC-7000PTn LED Name Status Description Off Camera is not powered (camera off) Power On Camera is correctl

1.6 Camera Installation Please follow the following instructions to set your IP camera up. 1. Unpack the product package and check if anything’s mi

3. Connect two antennas to the antenna bases, which is located at the back of this IP camera. 4. Place the camera at a secure place, and point th

5. Launch Internet Explorer on your computer, and following the instructions given in next section to set the IP camera. 13

Chapter II: Using Web Management Interface 2.1 Camera Settings The first menu after you logged onto web management interface is ‘Camera’, and this i

The descriptions of every setting in this menu will be given below: Item Description Pan/Tilt Speed Specifies the moving speed when you use pan / ti

NOTE: When you change any setting(s) listed above, please click ‘Apply’ button so the change(s) will take effect. For following functions, changes wi

2.2 Pan and Tilt This IP camera supports pan and tilt function, as you explored in last section. You can also make the camera move automatically in p

2.2.2 Grand Tour You can make the camera move between many pre-defined positions, and define the time you wish to pause at every position; this is ca

The descriptions of every setting in this menu will be given below: Item Description Name Input the name of this set of grand tour here. As you may

C A T A L O G Chapter I: Familiar with your Internet IP Camera...4 1.1 Package Contents...

2.2.3 Multi-Camera Display If you have more than one IC-5010 IP camera, you can view up to 9 videos captured by every camera, so you can monitor up t

Please note that the upper-left camera view always show the video of the camera you connected to and cannot be changed. The following example uses f

A new popup window will appear to allow you to set the information of camera. If you have popup blocker installed, you may have to disable it temporar

2.3 Network Settings All network-related settings can be found in this menu, and you have to specify TCP/IP parameters in this menu if you want to ch

The descriptions of every setting in this menu will be given below: Item Description Network Type This camera can obtain the IP address from DHCP se

2.3.2 WLAN The descriptions of every setting in this menu will be given below: Item Description Wireless Connection Select ‘Enable’ to activate

MAC Address: If you there are many wireless access points in proximity or some wireless access point hides it’s SSID, you can use MAC address to dist

2.3.3 Dynamic DNS If your ISP does not give you a fixed Internet IP address (i.e. the Internet address you’re using when you access the Internet is n

2.3.4 UPnP When UPnP function is activated, all UPnP-compatible computers / network devices will be able to discover this IP camera automatically (on

2.3.5 Login Free This camera provides a method to let unauthorized users to view the image captured by this camera, which is called as ‘LoginFree’. W

3-9 Snapshot ...66 3-10 Recording...

2.4 Motion Detection When you wish to use this camera to monitor the activities, motion detection function will be very useful. Camera will detect th

2.4.1 Motion Detection You can use this menu to setup basic motion detection settings: The descriptions of every setting in this menu will be give

2.4.2 Motion Region You can define the motion detection region within the image that camera captures, so this camera will ignore motions which are no

2.4.3 Email You can define the destination address of E-mail sending and mail server parameters here. The descriptions of every setting in this me

2.4.4 FTP Configuration You can set FTP server’s parameters here. The descriptions of every setting in this menu will be given below: Item Descr

2.4.5 SD Card Configuration You can define the filename and destination folder when saving a file in SD card. The descriptions of every setting in

2.5 System Info You can use this menu to get the operational information of this camera: … After you selected ‘System Info.’, a sub-menu will app

2.5.2 Date / Time Setting This setting allows you to change the date and time of the real time clock in this IP camera. You can set the time manually

2.5.3 Utilities This menu allows you to upgrade firmware, clear all settings, reboot the IP camera, and switch LED lights on/off. The descriptions

2.5.4 Status This menu provides all information about this IP camera, like firmware version, system uptime, date / time, and network information.

Chapter I: Familiar with your Internet IP Camera 1.1 Package Contents Thank you for purchasing this IP camera! Before you start to use this IP camer

2.6 Account If you wish to allow other people to view the live image captured by this camera, but don’t want to allow them to modify system settings,

When a user is added, it will be listed: The descriptions of every setting in this menu will be given below: Item Description Yes / No Enable or

2.7 SDHC … After you selected ‘System Info.’, a sub-menu will appear. There are 4 sub-menus available here: Please click the SD card setting yo

2.7.2 Space Alarm When you’re using SD card to store captured image and video clip, you can have this camera to send an E-mail to you when there’s on

Chapter III: Using Surveillance Software 3-1 Installing IP Camera Surveillance Software The IP camera surveillance software provides various functio

3. If you need installation program to create a desktop icon or a quick launch icon for you, click all items you need here, than click ‘Next’ to conti

6. The installing procedure will take some time, please be patient. 6. When you see this window, it means the software installing procedure is com

3-2 Using IP camera surveillance software You can click ‘IPCam Surveillance Software’ icon from desktop, quick launch bar, or start menu to start the

Full screen Click this button to switch to full screen mode (only display all camera’s image), press ‘ESC’ key to quit full screen mode. Scan Click

3-3 Configure IP camera surveillance software 3-3-1 Configure cameras Before you use this IP camera surveillance software, you must configure the ca

1.3 Product Highlights No pre-loaded software required - all you need is a browser like Internet Explorer 6 (and above, with plug-in installed).

3-3-1-1 ‘Camera’ tab In this tab you can configure all cameras you wish to connect. Up to 16 cameras can be connected simultaneously: Here are the

After you’ve set all channels you wish to set, click ‘OK’ to save settings, and if everything’s correct, you’ll see the camera’s image in IP camera su

Here are the descriptions of all setting items: Item Description Channel Select the channel number you wish to set. One Time Schedules You can speci

3-3-1-3 Audio For cameras that support audio, you can use this tab to decide if you wish to hear the audio captured by selected camera. Here are t

3-3-1-4 Motion Record With this function activated, only motions captured by the camera will be recorded, so you don’t have to waste hard disk storag

3-3-2 General Settings You can set system-wide settings of this IP camera surveillance software in this menu. 3-3-2-1 ‘General’ tab All general set

3-3-2-2 ‘E-Mail Setting’ tab If you want to use motion detection function and wish to get an email that contains the image captured by the camera, pl

SMTP port Specify the port number of the SMTP server you wish to use here. By default (and the setting of most of SMTP servers) it’s ‘25’. SMTP Auth S

3-3-2-3 Security If you don’t want other people to access this IP camera surveillance software, you can set a password to protect it. You’ll need to

3-3-2-4 About This tab shows the version number of the IP camera surveillance software you’re using. 59

1.4 Familiar with Key Components Front View The picture is similar with IC-7000PT Focus Ring Microphone IC7000PTn Power LED Audio LE

3-4 Change Display Layout This IP camera surveillance software provides 8 kinds of display layout: Every layout displays different number of came

Layout style 4: 8 Cameras Displays the video of up to 8 cameras. Layout style 5: 9 Cameras Displays the video of up to 9 cameras.

3-5 Full-screen modes If you want to use all available spaces on your monitor to display surveillance image, you can click ‘Full Screen’ button to sw

3-6 Scan If you have more than one camera configured, and you wish to switch the displaying image between cameras, you can click ‘Scan’ button to swi

3-7 Zoom-in / Zoom-out For cameras that support zoom-in / zoom-out function, you can use this function to see more objects that fall in the scope of

3-8 PTZ For cameras that support pan - tilt function, you can change the position that camera points to, to see different places that fall in the sco

3-9 Snapshot You can take a snapshot of selected camera and save it to ‘Snapshot’ sub-folder of pre-defined data directory. Click snapshot

3-11 Video Playback You can playback all recorded video by clicking this button. A new window will appear: You have to search the video

Chapter IV: Appendix 4.1 Specification Max Resolution: 640 x 480 pixels Sensor: 300K pixels 1/4" color CMOS sensor Gain control: Automatic Expo

694.2 Troubleshooting If the IP camera is not working properly, before you contact the dealer of purchase for help, please check the troubleshooting

Back View Ethernet Connector Antenna Power Connector WPS Button SD Card Slot Audio Connector z Antenna: Conne

70to send image by Email or FTP, but nothing is received anti-spam mechanism. b. Please make sure you have enough permission for FTP uploading (You

Side View Reset Button Reset Button: Press the button with pen nib and hold for 5 seconds to reset the camera settings

Bottom View Tripod Connector Tripod Connector: Connects to tripod to secure the camera when the camera is n